Coldglaze PRO 2 Clear Gloss-1.25 lt
Product Description
Description
WARNING!!! This is a flammable material and should NOT be used near an open flame. A heavy duty fume extractor, chemical respirator, gloves and goggles should be worn when handling and spraying.
Used on it's own Coldglaze PRO 2 will replace the glaze effect on china without the use of heat. It has excellent non-yellowing characteristics. It is also mixed with pigments to repaint patterns. Coldglaze PRO 2 is water resistant, very tough with high strength surface adhesion. It can be airbrushed even when mixed with powder pigments. Coldglaze PRO 2 can also be mixed with Oil Colors
FORCE DRYING To accelerate the drying process, a flash-off period of approximately 10 minutes should be allowed for the solvents to evaporate. Ceramic & Metal: Temperatures up to 120șC for 20 - 30 minutes normally recommended Plastic: Care must be taken to avoid deformation to the plastic. Typically, 60șC for 2 - 3 hours.
AIR DRYING Ambient temperature of 20șC, the drying time is approximately:
INSTRUCTIONS The mixing ratio is 4 parts resin to 1 part hardener by volume. Thoroughly mix with a small stirrer. pt146 Thinners may be added to thin the mix if required. Apply either by brush or airbrush. If required, add a small amount of pigment until the desired colour.
TO ACHIEVE A MATT FINISH For a matt finish, simply mix Sylmasta Matting Agent S532 with the Coldglaze PRO 2 to achieve desired finish. Mix quantities: 70g~80g of Matting Agent per litre of Coldglaze PRO 2.
TO CREATE A WHITE GLAZE A white glaze can be created in one of two ways: add 10% Sylmasta CGW White Paste for a high-quality, homogeneous white glaze. TO AIRBRUSH To the mixed Coldglaze PRO 2 add approximately 20% by volume of PRO 2 Thinners to obtain a suitable viscosity. Adjustments to the mix can be made, dependent upon desired finish. A wet film thickness of 50 - 60 microns will result in a dry film thickness of 25 microns. Surface Dry: 10 -15 Minutes Hard Dry: 2 - 4 Hours Full Properties: 7 Days Pot Life: 7 - 8 Hours
Used on it's own Coldglaze PRO 2 will replace the glaze effect on china without the use of heat. It has excellent non-yellowing characteristics. It is also mixed with pigments to repaint patterns. Coldglaze PRO 2 is water resistant, very tough with high strength surface adhesion. It can be airbrushed even when mixed with powder pigments. Coldglaze PRO 2 can also be mixed with Oil Colors
FORCE DRYING To accelerate the drying process, a flash-off period of approximately 10 minutes should be allowed for the solvents to evaporate. Ceramic & Metal: Temperatures up to 120șC for 20 - 30 minutes normally recommended Plastic: Care must be taken to avoid deformation to the plastic. Typically, 60șC for 2 - 3 hours.
AIR DRYING Ambient temperature of 20șC, the drying time is approximately:
INSTRUCTIONS The mixing ratio is 4 parts resin to 1 part hardener by volume. Thoroughly mix with a small stirrer. pt146 Thinners may be added to thin the mix if required. Apply either by brush or airbrush. If required, add a small amount of pigment until the desired colour.
TO ACHIEVE A MATT FINISH For a matt finish, simply mix Sylmasta Matting Agent S532 with the Coldglaze PRO 2 to achieve desired finish. Mix quantities: 70g~80g of Matting Agent per litre of Coldglaze PRO 2.
TO CREATE A WHITE GLAZE A white glaze can be created in one of two ways: add 10% Sylmasta CGW White Paste for a high-quality, homogeneous white glaze. TO AIRBRUSH To the mixed Coldglaze PRO 2 add approximately 20% by volume of PRO 2 Thinners to obtain a suitable viscosity. Adjustments to the mix can be made, dependent upon desired finish. A wet film thickness of 50 - 60 microns will result in a dry film thickness of 25 microns. Surface Dry: 10 -15 Minutes Hard Dry: 2 - 4 Hours Full Properties: 7 Days Pot Life: 7 - 8 Hours
Accessories
$98.00 | $55.00 |
Coldglaze PRO 2 Retarder $30.00 |